CNC XPRO V5 HOW TO
CNC XPRO V5 DRIVERS
CNC XPRO V5 32 BIT
CNC XPRO V5 FULL
CNC XPRO V5 PRO

The readings should show '1' for the normal state and '0.00' for the depressed state. Check the readings with the switch depressed and in its normal state. Put each probe on each of the limit switch terminals. To do a continuity test on the limit switch itself, detach the spade connectors.If the readings are as above, then the limit switch is working. The reading should show '1' with the switch in its default position and '0.00' when the switch has been depressed. To do a continuity test on the limit switch and its harness, put the probes on the screw terminals of the cable attached to the limit switch.This should be 0.00 when touching the probes together. Touch the two probes of the multimeter to get a baseline reading.Use your multimeter to do the continuity test.

CNC XPRO V5 HOW TO

Please refer to the tutorial below by ifixit on how to use a multimeter before proceeding with the steps below. The measurement should be identical to measuring from corner B to corner C. For example, measure from corner of end plate A to corner of end plate D. An assistant is recommended to get accurate results. Both diagonal measurements must be identical.

Ensure that your machine is square by checking the diagonal distance as shown below.

Spray your lead screw with PTFE lubricant and run the machine back and forth a few times.

Slightly tighten them and then move the machine to the back and fully tighten them.

CNC XPRO V5 FULL

Loosen the nut blocks a full turn or until there is a slight movement from the nut block. Please contact us at Adjust your nut blocks. Remove the lead screw from the machine and roll it on a flat surface like a garage floor or marble bench top.

If your machine is lead screw driven, check the lead screw for bends.

The wheels should be easy to move with a little bit of force. It should be smooth throughout the length of the gantry. Remove the lead screw and move the gantry by hand. Try to stall the motor by applying pressure to the motor coupling by hand.

De-couple the axis from the lead screw/gear/belt system and test the motor without a load applied to check if the problem is replicated.

Reduce the feed rates of your machine to 2500mm/min and acceleration to 800mm sec^2 and run the bench test again.

The feed rate settings are denoted by $X/MaxRate=3000 and acceleration is denoted by $X/Acceleration=100.000. Ensure that the acceleration and feed rate for lead screw driven machines is 3000mm/min and 100mm sec^2 or less respectively.

Check the motor settings by typing $S.

High impedance motors will stall much more quickly.

If you are using your own motors, please check the motor impedance in the motor’s datasheet.

Intermittent connections can cause erratic motor behavior.

Check to see that the EDG connectors throughout the wiring harness are gripping on the copper of the cable and not the cable insulation.

We recommend our MeanWell 24V 350W power supplies. Lower voltage power supplies can cause issues.

Check the power supply voltage is 24V ± 0.5V.

If the bench test passes, there may be mechanical, electrical or software issues putting extra stress on the motor.

As such, the xPRO V5 can be used with most current GRBL senders and post-processors. The xPRO V5 runs a 32bit port of the GRBL by Sonny Jeon.

CNC XPRO V5 PRO

The xPRO V5 comes fully assembled and programmed so all you need to do is wire up your motors and start cutting! The xPRO V5 is defaulted to support dual Y machines, or XYYZ, machines with motor current of 2.8A.įrom the computer side we have found the x PRO V5 WebUI (or CNCjs for USB mode (free/opensource)) are the best programs.

Selectable limit switch voltage (5V or 24v).

CNC XPRO V5 DRIVERS

4 software defined, independent motor drivers can:.Built-in Heatsink & Temperature Controlled Cooling Fan.USB-C interface work with GRBL sender programs.Sleek Web Interface with cut-from-SD capability (SD card included).

High Power 6A stepper drivers based on the Trinamic TMC5160.

CNC XPRO V5 32 BIT

The plug and play xPRO V5 brings you the advanced stepping and power of Trianamic drivers along with Wifi and USB interfaces, all powered by a 32 bit processor and wrapped in a beautiful ABS case (with integrated cooling).

Cnc xpro v5